Defort DWP-2000 User Manual download pdf (Page 7)

Plastic tube welding machine

Fig. 1-2

1 Supporting stand

2 Temperature adjusting screw

3 Handle

4 Heating element

5 Welding tools (heating spigot + socket)

6 Green power-on indicator lamp

7 Red temperature indicator lamp

Fig. 3

(1) Preparations

(2) Heating element

(3) Sleeve

(4) Heating spigot

(5) Heating socket

(6) Pipe

(7) Heating

(8) Completed joint

1. GENERAL POWER TOOL SAFETY WARN-

INGS

WARNING

To reduce the risk of injury, the user must read and un-

derstand the instruction manual.

Read all instructions. Failure to follow all instructions list-

ed below may result in electric shock, ﬁ re and/or serious

injury. The term ”power tool“ in all of the warnings listed

below refers to your mains operated (corded) power tool

or battery operated (cordless) power tool, also machines

and electric units. Only use the power tool for the pur-

pose for which it was intended, with the due attention to

the general safety and accident prevention regulations.

KEEP ALL SAFETY NOTES AND INSTRUCTIONS FOR

THE FUTURE.

A) Work area

a) Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂ ammable liq-

uids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose con-

trol.

B) Electrical safety

a) Power tool plugs must match the outlet. Never modi-

fy the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodiﬁ ed

plugs and matching outlets will reduce risk of elec-

tric shock. If the power tool comes with an earthed

wire, the plug may only be connected to an earthed

receptacle. At work sites, in damp surroundings, in

the open or in the case of comparable types of use,

only operate the power tool off the mains using a 30

mA fault current protected switch (FI breaker).

b) Avoid body contact with earthed or grounded surfac-

es such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for carry-

ing, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an ex-

tension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric

shock.

C) Personal safety

This appliance is not intended for use by persons (in-

cluding children) with reduced physical, sensory or men-

tal capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

Children should be supervised to ensure that they do not

play with the appliance.

a) Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use

a power tool while you are tired or under the inﬂ u-

ence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in

serious personal injury.

b) Use safety equipment. Always wear eye protec-

tion. Safety equipment such as dust mask, non skid

safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the

off position before plugging in. Carrying power tools

with your ﬁ nger on the switch or plugging in power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in per-

sonal injury.

e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of these devices

can reduce dust related hazards.

1 2 3 4 5 6 7 8 9 10 11 12 ... 87 88

Comments to this Manuals

No comments

Defort DWP-2000 User Manual Page 7

Comments to this Manuals